Drive Failure, code 201

Hi,

I need some help with my WD MyCloud 2TB, I logged in today onto my MyCloud web page and noticed a critical warning log which states drive failure (which was logged on the 7th March) and that I should contact WD support. The thing is, the actual homepage under diagnostics states the drive is healthy and also, I have been using it without much issues the last few weeks (touch wood), so was the error a false positive or should I be worried about the drive failing and consider replacing the unit?

Cheers,

Andrew


@sinder201 Have you run any test to see what happens and what the results show? See example image below. Click on, tap or activate image to enlarge it.

1 Like

Hi, thanks for the reply. Just ran a quick scan which showed no errors, will run a Full Test overnight and see if it identify any issues.

@sinder201 any type of Drive Failure Alert is always something to worry about!
BACKUP YOUR DATA!
Enable SSH
Login
type dmesg

Hi, just a small update, both disk tests identified no errors.

Hi, thanks for your advice, my main files are mirrored onto an external HDD as of last night when I discovered the warning lol.

Here’s the SSH Log:

BusyBox v1.20.2 (2015-02-25 14:32:43 CST) built-in shell (ash)
Enter ‘help’ for a list of built-in commands.

root@WDMyCloud root # dmesg
[ 0.000000] Booting Linux on physical CPU 0x0
[ 0.000000] Initializing cgroup subsys cpuset
[ 0.000000] Initializing cgroup subsys cpu
[ 0.000000] Initializing cgroup subsys cpuacct
[ 0.000000] Linux version 3.10.39 (kman@kmachine) (gcc version 4.6.4 (Linaro GCC branch-4.6.4. Marvell GCC Dev 201310-2126.3d181f66 64K MAXPAGESIZE ALIGN) ) #1 SMP Fri Aug 17 18:34:25 CST 2018 2014T20p4 Build-git435df54
[ 0.000000] CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
[ 0.000000] Machine: Marvell Armada 375 (Device Tree), model: Marvell Armada 375 Development Board
[ 0.000000] Memory policy: ECC disabled, Data cache writealloc
[ 0.000000] On node 0 totalpages: 16384
[ 0.000000] free_area_init_node: node 0, pgdat c07b2680, node_mem_map c0820000
[ 0.000000] Normal zone: 20 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 16384 pages, LIFO batch:3
[ 0.000000] PERCPU: Embedded 1 pages/cpu @c08d8000 s8064 r8192 d16512 u32768
[ 0.000000] pcpu-alloc: s8064 r8192 d16512 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0 [0] 1
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16364
[ 0.000000] Kernel command line: root=/dev/ram console=ttyS0,115200
[ 0.000000] PID hash table entries: 2048 (order: -2, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 3, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 2, 131072 bytes)
[ 0.000000] allocated 131072 bytes of page_cgroup
[ 0.000000] please try ‘cgroup_disable=memory’ option if you don’t want memory cgroups
[ 0.000000] Memory: 512MB = 512MB total
[ 0.000000] Memory: 511744k/511744k available, 12544k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
vector : 0xffff0000 - 0xffff8000 ( 32 kB)
fixmap : 0xffc00000 - 0xfff00000 (3072 kB)
vmalloc : 0xe0800000 - 0xfff00000 ( 503 MB)
lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
.text : 0xc0008000 - 0xc0719cd0 (7240 kB)
.init : 0xc0720000 - 0xc0761f80 ( 264 kB)
.data : 0xc0762000 - 0xc07b3c00 ( 327 kB)
.bss : 0xc07b3c00 - 0xc081d9fc ( 424 kB)
[ 0.000000] Hierarchical RCU implementation.
[ 0.000000] NR_IRQS:16 nr_irqs:16 16
[ 0.000000]
LSP version: linux-3.10.39-2014_T2.0p4

[ 0.000000] sched_clock: 32 bits at 25MHz, resolution 40ns, wraps every 171798ms
[ 0.000000] L310 cache controller enabled
[ 0.000000] l2x0: 8 ways, CACHE_ID 0x410054c9, AUX_CTRL 0x12040000, Cache size: 262144 B
[ 0.000000] Console: colour dummy device 80x30
[ 0.000775] Calibrating delay loop… 1594.16 BogoMIPS (lpj=7970816)
[ 0.090066] pid_max: default: 32768 minimum: 301
[ 0.090188] Mount-cache hash table entries: 4096
[ 0.090918] Initializing cgroup subsys memory
[ 0.090947] Initializing cgroup subsys devices
[ 0.091001] CPU: Testing write buffer coherency: ok
[ 0.091306] CPU0: thread -1, cpu 0, socket 0, mpidr 80000000
[ 0.091354] Setting up static identity map for 0xc055e960 - 0xc055e9b8
[ 0.091697] Initializing CPU Reset module
[ 0.092798] CPU1: Booted secondary processor
[ 0.131442] CPU1: thread -1, cpu 1, socket 0, mpidr 80000001
[ 0.131562] Brought up 2 CPUs
[ 0.131574] SMP: Total of 2 processors activated (3188.32 BogoMIPS).
[ 0.131578] CPU: All CPU(s) started in SVC mode.
[ 0.132498] devtmpfs: initialized
[ 0.136403] pinctrl core: initialized pinctrl subsystem
[ 0.136692] NET: Registered protocol family 16
[ 0.137346] DMA: preallocated 256 KiB pool for atomic coherent allocations
[ 0.141701] irq: Cannot allocate irq_descs @ IRQ193, assuming pre-allocated
[ 0.142542] irq: Cannot allocate irq_descs @ IRQ225, assuming pre-allocated
[ 0.142982] irq: Cannot allocate irq_descs @ IRQ257, assuming pre-allocated
[ 0.146903] hw-breakpoint: found 5 (+1 reserved) breakpoint and 1 watchpoint registers.
[ 0.146911] hw-breakpoint: maximum watchpoint size is 4 bytes.
[ 0.162517] bio: create slab at 0
[ 0.163313] mvebu-pcie pcie-controller.2: PCI host bridge to bus 0000:00
[ 0.163327] pci_bus 0000:00: root bus resource [io 0x1000-0xfffff]
[ 0.163335] pci_bus 0000:00: root bus resource [mem 0xe0000000-0xe8000000]
[ 0.163345] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 0.163371] PCI: bus0: Fast back to back transfers enabled
[ 0.163775] vgaarb: loaded
[ 0.164281] SCSI subsystem initialized
[ 0.164640] libata version 3.00 loaded.
[ 0.165181] usbcore: registered new interface driver usbfs
[ 0.165310] usbcore: registered new interface driver hub
[ 0.165495] usbcore: registered new device driver usb
[ 0.165883] pps_core: LinuxPPS API ver. 1 registered
[ 0.165889] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti giometti@linux.it
[ 0.165980] PTP clock support registered
[ 0.167291] Switching to clocksource armada_370_xp_clocksource
[ 0.178960] NET: Registered protocol family 2
[ 0.179460] TCP established hash table entries: 4096 (order: 0, 32768 bytes)
[ 0.179528] TCP bind hash table entries: 4096 (order: 0, 32768 bytes)
[ 0.179596] TCP: Hash tables configured (established 4096 bind 4096)
[ 0.179635] TCP: reno registered
[ 0.179645] UDP hash table entries: 1024 (order: 0, 32768 bytes)
[ 0.179705] UDP-Lite hash table entries: 1024 (order: 0, 32768 bytes)
[ 0.179954] NET: Registered protocol family 1
[ 0.180230] RPC: Registered named UNIX socket transport module.
[ 0.180236] RPC: Registered udp transport module.
[ 0.180240] RPC: Registered tcp transport module.
[ 0.180243] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.180252] PCI: CLS 0 bytes, default 64
[ 0.180392] Trying to unpack rootfs image as initramfs…
[ 0.180860] rootfs image is not initramfs (no cpio magic); looks like an initrd
[ 0.189365] Freeing initrd memory: 2528K (c0f08000 - c1180000)
[ 0.191655] VFS: Disk quotas dquot_6.5.2
[ 0.191802] Dquot-cache hash table entries: 8192 (order 0, 32768 bytes)
[ 0.192211] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.192468] Installing knfsd (copyright © 1996 okir@monad.swb.de).
[ 0.192717] jffs2: version 2.2. (NAND) \xffffffc2\xffffffa9 2001-2006 Red Hat, Inc.
[ 0.192807] fuse init (API version 7.22)
[ 0.193143] SGI XFS with security attributes, large block/inode numbers, no debug enabled
[ 0.193586] msgmni has been set to 1004
[ 0.195261] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 250)
[ 0.195271] io scheduler noop registered
[ 0.195276] io scheduler deadline registered
[ 0.195297] io scheduler cfq registered (default)
[ 0.196117] armada-375-pinctrl f1018000.pinctrl: registered pinctrl driver
[ 0.196816] mv_xor f1060800.xor: Marvell shared XOR driver
[ 0.238417] mv_xor f1060800.xor: Marvell XOR: ( xor cpy intr )
[ 0.238733] mv_xor f1060900.xor: Marvell shared XOR driver
[ 0.278430] mv_xor f1060900.xor: Marvell XOR: ( xor cpy intr )
[ 0.283311] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.305101] f1012000.serial: ttyS0 at MMIO 0xf1012000 (irq = 44) is a 16550A
[ 0.791626] console [ttyS0] enabled
[ 0.795376] brd: module loaded
[ 0.812916] loop: module loaded
[ 0.816387] sata_mv f10a0000.sata: version 1.28
[ 0.816557] sata_mv f10a0000.sata: slots 32 ports 2
[ 0.822509] scsi0 : sata_mv
[ 0.824439] scsi1 : sata_mv
[ 0.826225] ata1: SATA max UDMA/133 irq 58
[ 0.829066] ata2: SATA max UDMA/133 irq 58
[ 0.834475] m25p80 spi0.0: found mx25l8005, expected n25q128a13
[ 0.839162] m25p80 spi0.0: mx25l8005 (1024 Kbytes)
[ 0.846741] o PPv2.1 Giga driver
[ 0.848892] o 4 Giga ports supported
[ 0.851349] o BM supported for CPU: 8 BM pools
[ 0.854674] o HWF supported
[ 0.856345] o RX Queue support: 8 Queues * 128 Descriptors
[ 0.860761] o TX Queue support: 1 Queues * 532 Descriptors
[ 0.865135] o GSO supported
[ 0.866804] o Receive checksum offload supported
[ 0.870315] o Transmit checksum offload supported
[ 0.873904] o Driver ERROR statistics enabled
[ 0.877143] o Driver INFO statistics enabled

[ 0.984831] o Loading network interface(s) for port #0: cpu_mask=0x3, mtu=1500
[ 0.991193] o Port 0 is connected to Linux netdevice
[ 0.994970] o giga p=0: phy=0, mtu=1500, mac=00:50:43:02:02:00, speed=AutoNeg (platform)
[ 1.002991] txq_size 532 is not aligned 16, rounded to 528
[ 1.008633] o egiga0, ifindex = 2, GbE port = 0

[ 1.337384] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl F300)
[ 1.357587] ata1.00: ATA-9: WDC WD20EFRX-68EUZN0, 82.00A82, max UDMA/133
[ 1.363012] ata1.00: 3907029168 sectors, multi 0: LBA48 NCQ (depth 31/32)
[ 1.387573] ata1.00: configured for UDMA/133
[ 1.390923] scsi 0:0:0:0: Direct-Access ATA WDC WD20EFRX-68E 82.0 PQ: 0 ANSI: 5
[ 1.398619] sd 0:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 1.405093] sd 0:0:0:0: [sda] 4096-byte physical blocks
[ 1.409313] sd 0:0:0:0: [sda] Write Protect is off
[ 1.412824] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.413201] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn’t support DPO or FUA
[ 1.421195] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 1.462633] sda: sda1 sda2 sda3 sda4 sda5 sda6 sda7
[ 1.468593] sd 0:0:0:0: [sda] Attached SCSI disk
[ 1.767380] ata2: SATA link down (SStatus 0 SControl F300)
[ 2.014295] o Loading network interface(s) for port #1: cpu_mask=0x3, mtu=1500
[ 2.020654] o Port 1 is connected to Linux netdevice
[ 2.024430] o giga p=1: phy=3, mtu=1500, mac=00:50:43:02:02:01, speed=AutoNeg (platform)
[ 2.032452] txq_size 532 is not aligned 16, rounded to 528
[ 2.038262] o egiga1, ifindex = 3, GbE port = 1

[ 2.042207] libphy: orion_mdio_bus: probed
[ 2.045506] mdio_bus f10c0054.mdio-mi: cannot get PHY at address 3
[ 2.050979] ehci_hcd: USB 2.0 ‘Enhanced’ Host Controller (EHCI) Driver
[ 2.056229] ehci-pci: EHCI PCI platform driver
[ 2.059624] ehci-orion: EHCI orion driver
[ 2.062497] orion-ehci f1054000.usb: EHCI Host Controller
[ 2.066628] orion-ehci f1054000.usb: new USB bus registered, assigned bus number 1
[ 2.073526] orion-ehci f1054000.usb: irq 50, io mem 0xf1054000
[ 2.097405] orion-ehci f1054000.usb: USB 2.0 started, EHCI 1.00
[ 2.102701] hub 1-0:1.0: USB hub found
[ 2.105172] hub 1-0:1.0: 1 port detected
[ 2.108398] xhci-hcd f1058000.usb3: xHCI Host Controller
[ 2.112441] xhci-hcd f1058000.usb3: new USB bus registered, assigned bus number 2
[ 2.119372] xhci-hcd f1058000.usb3: irq 48, io mem 0xf1058000
[ 2.124269] xHCI xhci_add_endpoint called for root hub
[ 2.124275] xHCI xhci_check_bandwidth called for root hub
[ 2.124466] hub 2-0:1.0: USB hub found
[ 2.126935] hub 2-0:1.0: 1 port detected
[ 2.129719] xhci-hcd f1058000.usb3: xHCI Host Controller
[ 2.133766] xhci-hcd f1058000.usb3: new USB bus registered, assigned bus number 3
[ 2.140389] xHCI xhci_add_endpoint called for root hub
[ 2.140395] xHCI xhci_check_bandwidth called for root hub
[ 2.140587] hub 3-0:1.0: USB hub found
[ 2.143056] hub 3-0:1.0: 1 port detected
[ 2.146110] usbcore: registered new interface driver usb-storage
[ 2.151286] rtc-mv f1010300.rtc: rtc core: registered f1010300.rtc as rtc0
[ 2.157038] i2c /dev entries driver
[ 2.170253] mpcore_wdt: MPcore Watchdog Timer: 0.1. mpcore_noboot=0 mpcore_margin=60 sec (nowayout= 0)
[ 2.178831] softdog: Software Watchdog Timer: 0.08 initialized. soft_noboot=0 soft_margin=60 sec soft_panic=0 (nowayout=0)
[ 2.188640] md: linear personality registered for level -1
[ 2.192840] md: raid0 personality registered for level 0
[ 2.196866] md: raid1 personality registered for level 1
[ 2.201137] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) initialised: dm-devel@redhat.com
[ 2.208586] sdhci: Secure Digital Host Controller Interface driver
[ 2.213485] sdhci: Copyright© Pierre Ossman
[ 2.217029] sdhci-pltfm: SDHCI platform and OF driver helper
[ 2.221611] armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: Total CESA HW channels supported 2
[ 2.229679] armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources: CESA feature: int_coalescing(1)
[ 2.237471] armada-cesa-ocf f109d000.crypto: mv_get_cesa_resources threshold 0x2, threshold_time 0xff
[ 2.245592] mvCesaInit: channels=2, session=640, queue=64
[ 2.255142] armada-cesa-ocf f109d000.crypto: cesa_ocf_probe: CESA driver operate in ocf(0) mode
[ 2.263138] cesadev_init(c073c934)
[ 2.265994] TCP: cubic registered
[ 2.268051] NET: Registered protocol family 17
[ 2.271302] Bridge firewalling registered
[ 2.274026] 8021q: 802.1Q VLAN Support v1.8
[ 2.276975] VFP support v0.3: implementor 41 architecture 3 part 30 variant 9 rev 4
[ 2.283985] registered taskstats version 1
[ 2.287675] rtc-mv f1010300.rtc: setting system clock to 2013-01-08 21:17:05 UTC (1357679825)
[ 2.295288] md: Waiting for all devices to be available before autodetect
[ 2.300828] md: If you don’t use raid, use raid=noautodetect
[ 2.305994] md: Autodetecting RAID arrays.
[ 2.308826] md: Scanned 0 and added 0 devices.
[ 2.311979] md: autorun …
[ 2.313474] md: … autorun DONE.
[ 2.315604] RAMDISK: gzip image found at block 0
[ 2.477494] usb 3-1: new SuperSpeed USB device number 2 using xhci-hcd
[ 2.498454] usb 3-1: Parent hub missing LPM exit latency info. Power management will be impacted.
[ 2.508292] usb-storage 3-1:1.0: USB Mass Storage device detected
[ 2.515169] scsi2 : usb-storage 3-1:1.0
[ 2.839421] VFS: Mounted root (ext2 filesystem) readonly on device 1:0.
[ 2.844899] devtmpfs: mounted
[ 2.846778] Freeing unused kernel memory: 256K (c0720000 - c0760000)
[ 3.519913] scsi 2:0:0:0: Direct-Access TOSHIBA External USB 3.0 5438 PQ: 0 ANSI: 6
[ 3.527894] sd 2:0:0:0: Attached scsi generic sg1 type 0
[ 3.532032] sd 2:0:0:0: [sdb] 3907029160 512-byte logical blocks: (2.00 TB/1.81 TiB)
[ 3.538894] sd 2:0:0:0: [sdb] Write Protect is off
[ 3.542404] sd 2:0:0:0: [sdb] Mode Sense: 23 00 00 00
[ 3.542748] sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn’t support DPO or FUA
[ 3.558788] sdb: sdb1
[ 3.562757] sd 2:0:0:0: [sdb] Attached SCSI disk
[ 5.060152] EXT3-fs (sda3): error: couldn’t mount because of unsupported optional features (240)
[ 5.068646] EXT2-fs (sda3): error: couldn’t mount because of unsupported optional features (244)
[ 5.138096] EXT4-fs (sda3): recovery complete
[ 5.197421] EXT4-fs (sda3): mounted filesystem with ordered data mode. Opts: (null)
[ 5.368066] EXT4-fs (sda7): recovery complete
[ 5.407423] EXT4-fs (sda7): mounted filesystem with ordered data mode. Opts: (null)
[ 14.042390] jnl: driver (lke_9.2.0 lke_9.2.0_r256412_b8, LBD=ON) loaded at bf000000
[ 14.176284] ufsd: module license ‘Commercial product’ taints kernel.
[ 14.181390] Disabling lock debugging due to kernel taint
[ 14.192925] ufsd:: trace mask set to 0000000f
[ 14.196020] ufsd: driver (lke_9.2.0 lke_9.2.0_r256412_b8, build_host(“swtest6”), acl, ioctl, bdi, sd2(0), fua, bz, tr, rsrc) loaded at bf020000
NTFS support included
Hfs+/HfsJ support included
optimized: speed
Build_for__WD_Glacier_k3.10.39_2015-08-11_lke_9.2.0_r256412_b8

[ 14.248895] tun: Universal TUN/TAP device driver, 1.6
[ 14.252680] tun: © 1999-2004 Max Krasnyansky maxk@qualcomm.com
[ 19.208295] EXT4-fs (sda6): mounted filesystem with ordered data mode. Opts: (null)
[ 19.394740] egiga0: mac address changed
[ 19.409306] SWF long pool #0: pkt_size=1536, buf_size=1600, total_size=1792 - 1024 of 1024 buffers added
[ 19.420086] SWF short pool #3: pkt_size= 256, buf_size= 320, total_size= 512 - 2048 of 2048 buffers added
[ 19.433210] HWF long pool #4: pkt_size=1536, buf_size=1568, total_size=1568 - 1024 of 1024 buffers added
[ 19.445565] HWF short pool #7: pkt_size= 480, buf_size= 512, total_size= 512 - 2048 of 2048 buffers added
[ 19.454171] egiga0: started
[ 19.454204] egiga0: link up, full duplex, speed 1 Gbps
[ 19.459542] egiga0: link up, full duplex, speed 1 Gbps
[ 28.227722] md: bind
[ 28.231997] md/raid1:md0: active with 1 out of 2 mirrors
[ 28.236217] md0: bitmap file is out of date (0 < 1) – forcing full recovery
[ 28.242059] created bitmap (16 pages) for device md0
[ 28.245811] md0: bitmap file is out of date, doing full recovery
[ 28.438320] md0: bitmap initialized from disk: read 2 pages, set 262136 of 262136 bits
[ 28.457430] md0: detected capacity change from 0 to 2147418112
[ 28.470767] md0: unknown partition table
[ 28.531377] Adding 2097056k swap on /dev/md0. Priority:-1 extents:1 across:2097056k
[ 28.580102] EXT4-fs (sda4): barriers disabled
[ 28.611137] EXT4-fs (sda4): recovery complete
[ 28.614367] EXT4-fs (sda4): mounted filesystem with ordered data mode. Opts: barrier=0,usrquota,grpquota
[ 32.979027] EXT4-fs (sda2): barriers disabled
[ 33.537843] EXT4-fs (sda2): recovery complete
[ 33.541180] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: barrier=0,usrquota,grpquota
[ 33.661003] restart sysinfod…
[ 42.390089] ufsd: “mount” (sdb1): is mounted as NTFS (without journal)
[ 47.911378] scandisk for power failure now.
[ 50.382743] volume_stop.sh /mnt/HD/HD_a2…
[ 50.511436] kill_process.sh /mnt/HD/HD_a2…
[ 50.672704] kill_process.sh done.
[ 51.782592] volume_stop.sh done.
[ 176.042658] EXT4-fs (sda2): barriers disabled
[ 176.378104] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: barrier=0,usrquota,grpquota
[249484.437348] egiga0: link down
[249538.560396] egiga0: link up, full duplex, speed 1 Gbps
[249542.895462] egiga0: link down
[249598.887080] egiga0: link up, full duplex, speed 1 Gbps
[249713.026947] egiga0: link down
[249716.023547] egiga0: link up, full duplex, speed 1 Gbps
[249723.355404] egiga0: link down
[249726.302148] egiga0: link up, full duplex, speed 1 Gbps
[263123.034714] egiga0: link down
[263164.195674] egiga0: link up, full duplex, speed 1 Gbps
[263276.504295] egiga0: link down
[263279.408215] egiga0: link up, full duplex, speed 1 Gbps
[263287.194596] egiga0: link down
[263290.061082] egiga0: link up, full duplex, speed 1 Gbps
[1030312.186118] EXT4-fs (sda2): re-mounted. Opts: barrier=0,usrquota,grpquota,init_itable=10
[1041907.247789] EXT4-fs (sda2): re-mounted. Opts: barrier=0,usrquota,grpquota,init_itable=10,init_itable=10
[1068837.372770] EXT4-fs (sda2): re-mounted. Opts: barrier=0,usrquota,grpquota,init_itable=10,init_itable=10,init_itable=10
[1127101.091496] failed to map v2l.vbo 296000
root@WDMyCloud root #