smartctl 6.6 2017-11-05 r4594 [x86_64-linux-4.19.0-9-amd64] (local build) Copyright (C) 2002-17, Bruce Allen, Christian Franke, www.smartmontools.org === START OF INFORMATION SECTION === Model Family: Western Digital Blue Device Model: WDC WD40EZRZ-00GXCB0 Serial Number: WD-WCC7K1YU4D7Z LU WWN Device Id: 5 0014ee 2676691e2 Firmware Version: 80.00A80 User Capacity: 4,000,787,030,016 bytes [4.00 TB] Sector Sizes: 512 bytes logical, 4096 bytes physical Rotation Rate: 5400 rpm Form Factor: 3.5 inches Device is: In smartctl database [for details use: -P show] ATA Version is: ACS-3 T13/2161-D revision 5 SATA Version is: SATA 3.1, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Fri Jul 17 12:58:24 2020 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled === START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED General SMART Values: Offline data collection status: (0x82) Offline data collection activity was completed without error. Auto Offline Data Collection: Enabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: (42720) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 2) minutes. Extended self-test routine recommended polling time: ( 453) minutes. Conveyance self-test routine recommended polling time: ( 5) minutes. SCT capabilities: (0x3035) SCT Status supported. SCT Feature Control supported. SCT Data Table supported. SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x002f 100 253 051 Pre-fail Always - 0 3 Spin_Up_Time 0x0027 169 169 021 Pre-fail Always - 6508 4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 27 5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0 7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0 9 Power_On_Hours 0x0032 098 098 000 Old_age Always - 1805 10 Spin_Retry_Count 0x0032 100 253 000 Old_age Always - 0 11 Calibration_Retry_Count 0x0032 100 253 000 Old_age Always - 0 12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 9 192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 2 193 Load_Cycle_Count 0x0032 200 200 000 Old_age Always - 597 194 Temperature_Celsius 0x0022 119 112 000 Old_age Always - 31 196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0 197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0 198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0 199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0 200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0 SMART Error Log Version: 1 ATA Error Count: 16287 (device log contains only the most recent five errors) CR = Command Register [HEX] FR = Features Register [HEX] SC = Sector Count Register [HEX] SN = Sector Number Register [HEX] CL = Cylinder Low Register [HEX] CH = Cylinder High Register [HEX] DH = Device/Head Register [HEX] DC = Device Command Register [HEX] ER = Error register [HEX] ST = Status register [HEX] Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes, SS=sec, and sss=millisec. It "wraps" after 49.710 days. Error 16287 occurred at disk power-on lifetime: 1791 hours (74 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 00 00 00 00 a0 Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- e0 00 00 00 00 00 a0 08 00:27:04.661 STANDBY IMMEDIATE b0 da 00 00 4f c2 00 08 00:20:37.867 SMART RETURN STATUS b0 d0 01 00 4f c2 00 08 00:20:37.864 SMART READ DATA b0 d1 01 00 4f c2 00 08 00:20:37.861 SMART READ ATTRIBUTE THRESHOLDS [OBS-4] ec 00 01 00 00 00 00 08 00:20:37.861 IDENTIFY DEVICE Error 16286 occurred at disk power-on lifetime: 1791 hours (74 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 02 00 00 00 a0 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 10 02 00 00 00 a0 08 00:16:31.500 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 08 00:16:31.499 IDENTIFY DEVICE ef 03 46 00 00 00 a0 08 00:16:31.499 SET FEATURES [Set transfer mode] ef 10 02 00 00 00 a0 08 00:16:31.499 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 08 00:16:31.499 IDENTIFY DEVICE Error 16285 occurred at disk power-on lifetime: 1791 hours (74 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 46 00 00 00 a0 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 03 46 00 00 00 a0 08 00:16:31.499 SET FEATURES [Set transfer mode] ef 10 02 00 00 00 a0 08 00:16:31.499 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 08 00:16:31.499 IDENTIFY DEVICE ef 10 02 00 00 00 a0 08 00:16:31.474 SET FEATURES [Enable SATA feature] Error 16284 occurred at disk power-on lifetime: 1791 hours (74 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 02 00 00 00 a0 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 10 02 00 00 00 a0 08 00:16:31.499 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 08 00:16:31.499 IDENTIFY DEVICE ef 10 02 00 00 00 a0 08 00:16:31.474 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 08 00:16:31.473 IDENTIFY DEVICE Error 16283 occurred at disk power-on lifetime: 1791 hours (74 days + 15 hours) When the command that caused the error occurred, the device was active or idle. After command completion occurred, registers were: ER ST SC SN CL CH DH -- -- -- -- -- -- -- 04 61 02 00 00 00 a0 Device Fault; Error: ABRT Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ef 10 02 00 00 00 a0 08 00:16:31.474 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 08 00:16:31.473 IDENTIFY DEVICE ef 03 46 00 00 00 a0 08 00:16:31.473 SET FEATURES [Set transfer mode] ef 10 02 00 00 00 a0 08 00:16:31.473 SET FEATURES [Enable SATA feature] ec 00 00 00 00 00 a0 08 00:16:31.471 IDENTIFY DEVICE SMART Self-test log structure revision number 1 Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error # 1 Extended offline Completed without error 00% 1805 - # 2 Extended offline Completed without error 00% 1581 - # 3 Extended offline Aborted by host 10% 1573 - # 4 Extended offline Completed without error 00% 1515 - # 5 Short offline Completed without error 00% 1515 - SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.