Hi,
here is the dmesg (throught ssh) I got from a WD Wireless.
Machine: am335xevm
I guess it would be feasible to get openwrt.
https://downloads.openwrt.org/snapshots/trunk/omap/generic/
Best regards
dmesg
[ 0.000000] Linux version 3.2.0 (primax@primax-vm) (gcc version 4.7.3 20130226 (prerelease) (crosstool-NG linaro-1.13.1-4.7-2013.03-20130313 - Linaro GCC 2013.03) ) #1 Tue Sep 8 14:42:47 CST 2015
[ 0.000000] CPU: ARMv7 Processor [413fc082] revision 2 (ARMv7), cr=10c53c7d
[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
[ 0.000000] Machine: am335xevm
[ 0.000000] Memory policy: ECC disabled, Data cache writeback
[ 0.000000] On node 0 totalpages: 131072
[ 0.000000] free_area_init_node: node 0, pgdat c054f120, node_mem_map c0586000
[ 0.000000] Normal zone: 1024 pages used for memmap
[ 0.000000] Normal zone: 0 pages reserved
[ 0.000000] Normal zone: 130048 pages, LIFO batch:31
[ 0.000000] AM335X ES2.1 (neon )
[ 0.000000] pcpu-alloc: s0 r0 d32768 u32768 alloc=1*32768
[ 0.000000] pcpu-alloc: [0] 0
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 130048
[ 0.000000] Kernel command line: console=ttyO0,115200n8 root=ubi0:rootfs rw ubi.mtd=7,2048 rootfstype=ubifs rootwait=1
[ 0.000000] PID hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.000000] Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.000000] allocated 2097152 bytes of page_cgroup
[ 0.000000] please try ‘cgroup_disable=memory’ option if you don’t want memory cgroups
[ 0.000000] Memory: 512MB = 512MB total
[ 0.000000] Memory: 512048k/512048k available, 12240k reserved, 0K highmem
[ 0.000000] Virtual kernel memory layout:
[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
[ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
[ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)
[ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
[ 0.000000] modules : 0xbf000000 - 0xc0000000 ( 16 MB)
[ 0.000000] .text : 0xc0008000 - 0xc04c4000 (4848 kB)
[ 0.000000] .init : 0xc04c4000 - 0xc04fb000 ( 220 kB)
[ 0.000000] .data : 0xc04fc000 - 0xc0557360 ( 365 kB)
[ 0.000000] .bss : 0xc0557384 - 0xc0585b74 ( 186 kB)
[ 0.000000] NR_IRQS:396
[ 0.000000] IRQ: Found an INTC at 0xfa200000 (revision 5.0) with 128 interrupts
[ 0.000000] Total of 128 interrupts on 1 active controller
[ 0.000000] OMAP clockevent source: GPTIMER2 at 24000000 Hz
[ 0.000000] omap_dm_timer_switch_src: Switching to HW default clocksource(sys_clkin_ck) for timer1, this may impact timekeeping in low power state
[ 0.000000] OMAP clocksource: GPTIMER1 at 24000000 Hz
[ 0.000000] sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
[ 0.000000] Console: colour dummy device 80x30
[ 0.000176] Calibrating delay loop… 795.44 BogoMIPS (lpj=3977216)
[ 0.037389] pid_max: default: 32768 minimum: 301
[ 0.037499] Security Framework initialized
[ 0.037588] Mount-cache hash table entries: 512
[ 0.037928] Initializing cgroup subsys memory
[ 0.037996] CPU: Testing write buffer coherency: ok
[ 0.038675] devtmpfs: initialized
[ 0.057929] omap_hwmod: gfx: failed to hardreset
[ 0.073799] omap_hwmod: pruss: failed to hardreset
[ 0.074827] print_constraints: dummy:
[ 0.075137] NET: Registered protocol family 16
[ 0.077065] OMAP GPIO hardware version 0.1
[ 0.079102] omap_mux_init: Add partition: #1: core, flags: 0
[ 0.080858] omap_i2c.1: alias fck already exists
[ 0.082307] edma.0: alias fck already exists
[ 0.082328] edma.0: alias fck already exists
[ 0.082344] edma.0: alias fck already exists
[ 0.098407] bio: create slab at 0
[ 0.100244] SCSI subsystem initialized
[ 0.100884] usbcore: registered new interface driver usbfs
[ 0.101154] usbcore: registered new interface driver hub
[ 0.101344] usbcore: registered new device driver usb
[ 0.101636] registerd cppi-dma Intr @ IRQ 17
[ 0.101649] Cppi41 Init Done Qmgr-base(e087a000) dma-base(e0878000)
[ 0.101658] Cppi41 Init Done
[ 0.101684] musb-ti81xx musb-ti81xx: musb0, board_mode=0x11, plat_mode=0x1
[ 0.101973] musb-ti81xx musb-ti81xx: musb1, board_mode=0x11, plat_mode=0x1
[ 0.117405] omap_i2c omap_i2c.1: bus 1 rev2.4.0 at 100 kHz
[ 0.119003] tps65910 1-002d: JTAGREVNUM 0x1
[ 0.123819] print_constraints: VRTC:
[ 0.125227] print_constraints: VIO: at 1500 mV
[ 0.127479] print_constraints: VDD1: 600 <–> 1500 mV at 1262 mV normal
[ 0.129732] print_constraints: VDD2: 600 <–> 1500 mV at 1137 mV normal
[ 0.130717] print_constraints: VDD3: 5000 mV
[ 0.132098] print_constraints: VDIG1: at 1800 mV
[ 0.133488] print_constraints: VDIG2: at 1800 mV
[ 0.134875] print_constraints: VPLL: at 1800 mV
[ 0.136259] print_constraints: VDAC: at 1800 mV
[ 0.137648] print_constraints: VAUX1: at 1800 mV
[ 0.139040] print_constraints: VAUX2: at 3300 mV
[ 0.140421] print_constraints: VAUX33: at 3300 mV
[ 0.141804] print_constraints: VMMC: at 3300 mV
[ 0.142262] tps65910 1-002d: No interrupt support, no core IRQ
[ 0.145424] Switching to clocksource gp timer
[ 0.161967] musb-hdrc: version 6.0, ?dma?, otg (peripheral+host)
[ 0.162131] musb-hdrc musb-hdrc.0: dma type: dma-cppi41
[ 0.162421] MUSB0 controller’s USBSS revision = 4ea20800
[ 0.162442] TxFifo Empty intr disabled
[ 0.162451] musb0: Enabled SW babble control
[ 0.162704] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[ 0.162721] musb-hdrc: MHDRC RTL version 2.0
[ 0.162730] musb-hdrc: setup fifo_mode 4
[ 0.162756] musb-hdrc: 28/31 max ep, 16384/16384 memory
[ 0.162770] musb-hdrc.0: bulk split disabled
[ 0.162777] musb-hdrc.0: bulk combine disabled
[ 0.162861] musb-hdrc musb-hdrc.0: MUSB HDRC host driver
[ 0.162952] musb-hdrc musb-hdrc.0: new USB bus registered, assigned bus number 1
[ 0.163067] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.163081] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.163093] usb usb1: Product: MUSB HDRC host driver
[ 0.163102] usb usb1: Manufacturer: Linux 3.2.0 musb-hcd
[ 0.163111] usb usb1: SerialNumber: musb-hdrc.0
[ 0.163981] hub 1-0:1.0: USB hub found
[ 0.164009] hub 1-0:1.0: 1 port detected
[ 0.164560] musb-hdrc musb-hdrc.0: USB Host mode controller at e083c000 using DMA, IRQ 18
[ 0.164722] musb-hdrc musb-hdrc.1: dma type: dma-cppi41
[ 0.165008] MUSB1 controller’s USBSS revision = 4ea20800
[ 0.165026] TxFifo Empty intr disabled
[ 0.165033] musb1: Enabled SW babble control
[ 0.165274] musb-hdrc: ConfigData=0xde (UTMI-8, dyn FIFOs, bulk combine, bulk split, HB-ISO Rx, HB-ISO Tx, SoftConn)
[ 0.165289] musb-hdrc: MHDRC RTL version 2.0
[ 0.165298] musb-hdrc: setup fifo_mode 4
[ 0.165322] musb-hdrc: 28/31 max ep, 16384/16384 memory
[ 0.165335] musb-hdrc.1: bulk split disabled
[ 0.165342] musb-hdrc.1: bulk combine disabled
[ 0.165413] musb-hdrc musb-hdrc.1: MUSB HDRC host driver
[ 0.165524] musb-hdrc musb-hdrc.1: new USB bus registered, assigned bus number 2
[ 0.165616] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.165630] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.165641] usb usb2: Product: MUSB HDRC host driver
[ 0.165650] usb usb2: Manufacturer: Linux 3.2.0 musb-hcd
[ 0.165659] usb usb2: SerialNumber: musb-hdrc.1
[ 0.166422] hub 2-0:1.0: USB hub found
[ 0.166446] hub 2-0:1.0: 1 port detected
[ 0.166947] musb-hdrc musb-hdrc.1: USB Host mode controller at e083e800 using DMA, IRQ 19
[ 0.167343] NET: Registered protocol family 2
[ 0.167513] IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.167797] TCP established hash table entries: 16384 (order: 5, 131072 bytes)
[ 0.168064] TCP bind hash table entries: 16384 (order: 4, 65536 bytes)
[ 0.168221] TCP: Hash tables configured (established 16384 bind 16384)
[ 0.168232] TCP reno registered
[ 0.168243] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.168263] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.168437] NET: Registered protocol family 1
[ 0.168666] RPC: Registered named UNIX socket transport module.
[ 0.168678] RPC: Registered udp transport module.
[ 0.168685] RPC: Registered tcp transport module.
[ 0.168693] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.168892] NetWinder Floating Point Emulator V0.97 (double precision)
[ 0.186872] VFS: Disk quotas dquot_6.5.2
[ 0.186932] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
[ 0.187417] fuse init (API version 7.17)
[ 0.188010] msgmni has been set to 1000
[ 0.190816] alg: No test for stdrng (krng)
[ 0.191450] io scheduler noop registered
[ 0.191462] io scheduler deadline registered
[ 0.191533] io scheduler cfq registered (default)
[ 0.192621] omap_uart.0: ttyO0 at MMIO 0x44e09000 (irq = 72) is a OMAP UART0
[ 0.192806] console [ttyO0] enabled
[ 0.193323] omap_uart.1: ttyO1 at MMIO 0x48022000 (irq = 73) is a OMAP UART1
[ 0.193776] omap_uart.2: ttyO2 at MMIO 0x48024000 (irq = 74) is a OMAP UART2
[ 0.194204] omap_uart.3: ttyO3 at MMIO 0x481a6000 (irq = 44) is a OMAP UART3
[ 0.194619] omap_uart.4: ttyO4 at MMIO 0x481a8000 (irq = 45) is a OMAP UART4
[ 0.195039] omap_uart.5: ttyO5 at MMIO 0x481aa000 (irq = 46) is a OMAP UART5
[ 0.195978] omap4_rng omap4_rng: OMAP4 Random Number Generator ver. 2.00
[ 0.196133] am335x_gpio initializing
[ 0.205218] brd: module loaded
[ 0.210072] loop: module loaded
[ 0.210149] at24 1-0051: 32768 byte 24c256 EEPROM, writable, 64 bytes/write
[ 0.285483] No daughter card found
[ 0.285535] at24 1-0050: 32768 byte 24c256 EEPROM, writable, 64 bytes/write
[ 0.365462] AM335X: EVM Config read fail: -110
[ 0.385461] The board is general purpose EVM in profile 0
[ 0.386469] omap-gpmc omap-gpmc: GPMC revision 6.0
[ 0.386487] Registering NAND on CS0
[ 0.387270] omap_hsmmc.0: alias fck already exists
[ 0.387543] omap_hsmmc.2: alias fck already exists
[ 0.390086] registered am33xx_sr device
[ 0.391682] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 0.392020] omap2-nand driver initializing
[ 0.392333] ONFI flash detected
[ 0.392463] ONFI param page 0 valid
[ 0.392479] NAND device: Manufacturer ID: 0xad, Chip ID: 0xf1 (Hynix H27U1G8F2BTR-BC)
[ 0.392679] Creating 10 MTD partitions on “omap2-nand.0”:
[ 0.392697] 0x000000000000-0x000000020000 : “SPL”
[ 0.394149] 0x000000020000-0x000000040000 : “SPL.backup1”
[ 0.395445] 0x000000040000-0x000000060000 : “SPL.backup2”
[ 0.396804] 0x000000060000-0x000000080000 : “SPL.backup3”
[ 0.398117] 0x000000080000-0x000000260000 : “U-Boot”
[ 0.400093] 0x000000260000-0x000000280000 : “U-Boot Env”
[ 0.401308] 0x000000280000-0x000000780000 : “Kernel”
[ 0.404551] 0x000000780000-0x000007b00000 : “File System”
[ 0.453293] 0x000007b00000-0x000007c00000 : “DefCfg”
[ 0.454911] 0x000007c00000-0x000008000000 : “Recovery”
[ 0.457964] OneNAND driver initializing
[ 0.458686] UBI: attaching mtd7 to ubi0
[ 0.458704] UBI: physical eraseblock size: 131072 bytes (128 KiB)
[ 0.458713] UBI: logical eraseblock size: 126976 bytes
[ 0.458721] UBI: smallest flash I/O unit: 2048
[ 0.458729] UBI: VID header offset: 2048 (aligned 2048)
[ 0.458737] UBI: data offset: 4096
[ 0.646342] usb 2-1: new high-speed USB device number 2 using musb-hdrc
[ 0.806656] usb 2-1: New USB device found, idVendor=1058, idProduct=083c
[ 0.806671] usb 2-1: New USB device strings: Mfr=2, Product=3, SerialNumber=1
[ 0.806682] usb 2-1: Product: My Passport 083C
[ 0.806691] usb 2-1: Manufacturer: Western Digital
[ 0.806700] usb 2-1: SerialNumber: 313634373134433132394630
[ 1.438983] UBI: max. sequence number: 551
[ 1.452624] UBI: attached mtd7 to ubi0
[ 1.452638] UBI: MTD device name: “File System”
[ 1.452647] UBI: MTD device size: 115 MiB
[ 1.452654] UBI: number of good PEBs: 924
[ 1.452662] UBI: number of bad PEBs: 0
[ 1.452669] UBI: number of corrupted PEBs: 0
[ 1.452676] UBI: max. allowed volumes: 128
[ 1.452683] UBI: wear-leveling threshold: 4096
[ 1.452690] UBI: number of internal volumes: 1
[ 1.452697] UBI: number of user volumes: 1
[ 1.452704] UBI: available PEBs: 0
[ 1.452712] UBI: total number of reserved PEBs: 924
[ 1.452719] UBI: number of PEBs reserved for bad PEB handling: 9
[ 1.452728] UBI: max/mean erase counter: 6/2
[ 1.452736] UBI: image sequence number: 809690822
[ 1.452773] Initializing USB Mass Storage driver…
[ 1.452992] UBI: background thread “ubi_bgt0d” started, PID 509
[ 1.453103] scsi0 : usb-storage 2-1:1.0
[ 1.454010] usbcore: registered new interface driver usb-storage
[ 1.454023] USB Mass Storage support registered.
[ 1.461945] tps65910-rtc tps65910-rtc: rtc core: registered tps65910-rtc as rtc0
[ 1.462139] i2c /dev entries driver
[ 1.463349] OMAP Watchdog Timer Rev 0x01: initial timeout 60 sec
[ 1.465583] cpuidle: using governor ladder
[ 1.466037] cpuidle: using governor menu
[ 1.469500] omap4_aes_mod_init: loading AM33X AES driver
[ 1.469598] omap4-aes omap4-aes: AM33X AES hw accel rev: 3.02
[ 1.470076] omap4_aes_probe: probe() done
[ 1.470279] omap4_sham_mod_init: loading AM33X SHA/MD5 driver
[ 1.470393] omap4-sham omap4-sham: AM33X SHA/MD5 hw accel rev: 4.03
[ 1.474901] omap4_sham_probe: probe() done
[ 1.475304] oprofile: hardware counters not available
[ 1.475315] oprofile: using timer interrupt.
[ 1.475351] nf_conntrack version 0.5.0 (8000 buckets, 32000 max)
[ 1.475880] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 1.475999] TCP cubic registered
[ 1.476012] NET: Registered protocol family 17
[ 1.476060] Registering the dns_resolver key type
[ 1.476129] VFP support v0.3: implementor 41 architecture 3 part 30 variant c rev 3
[ 1.476150] ThumbEE CPU extension supported.
[ 1.476217] mux: Failed to setup hwmod io irq -22
[ 1.476833] Power Management for AM33XX family
[ 1.477040] Trying to load am335x-pm-firmware.bin (60 secs timeout)
[ 1.477175] Copied the M3 firmware to UMEM
[ 1.477264] Cortex M3 Firmware Version = 0x181
[ 1.477334] DIEID: 0801a024 014fcfb3 00000000 584c0002
[ 1.477343] EFUSE SMA register val = 00013e2f
[ 1.477363] Compensating OPP0: Orig nvalue:0x99c5b4 New nvalue:0x99c5b4
[ 1.477377] Compensating OPP1: Orig nvalue:0x998f81 New nvalue:0x998f81
[ 1.478842] Compensating OPP0: Orig nvalue:0x99bdad New nvalue:0x99bdad
[ 1.478858] Compensating OPP1: Orig nvalue:0x999484 New nvalue:0x999484
[ 1.478870] Compensating OPP2: Orig nvalue:0xaaebd3 New nvalue:0xaaebd3
[ 1.478882] Compensating OPP3: Orig nvalue:0xaacab5 New nvalue:0xaacab5
[ 1.478895] Compensating OPP4: Orig nvalue:0xaacab5 New nvalue:0xaa9a8d
[ 1.478953] create_regulator: VDD1: Failed to create debugfs directory
[ 1.480459] smartreflex smartreflex: am33xx_sr_probe: Driver initialized
[ 1.486498] clock: disabling unused clocks to save power
[ 1.501086] tps65910-rtc tps65910-rtc: setting system clock to 2017-02-22 16:02:03 UTC (1487779323)
[ 1.566157] UBIFS: recovery needed
[ 1.732039] SR 0: curr=1137500, delta_v=-56875, calc=1080625, act=1087500, gain=00
[ 1.738130] SR 1: curr=1262500, delta_v=-63125, calc=1199375, act=1200000, gain=00
[ 1.917212] UBIFS: recovery completed
[ 1.917235] UBIFS: mounted UBI device 0, volume 0, name “rootfs”
[ 1.917248] UBIFS: file system size: 114278400 bytes (111600 KiB, 108 MiB, 900 LEBs)
[ 1.917262] UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
[ 1.917273] UBIFS: media format: w4/r0 (latest is w4/r0)
[ 1.917281] UBIFS: default compressor: lzo
[ 1.917289] UBIFS: reserved for root: 0 bytes (0 KiB)
[ 1.918446] VFS: Mounted root (ubifs filesystem) on device 0:14.
[ 1.921076] devtmpfs: mounted
[ 1.921371] Freeing init memory: 220K
[ 2.020434] mmc1: card claims to support voltages below the defined range. These will be ignored.
[ 2.118857] mmc1: queuing unknown CIS tuple 0x91 (3 bytes)
[ 2.135029] mmc1: new high speed SDIO card at address 0001
[ 2.452307] scsi 0:0:0:0: Direct-Access WD My Passport 083C 1009 PQ: 0 ANSI: 6
[ 2.453242] scsi 0:0:0:1: Direct-Access WD My Passport 083C 1009 PQ: 0 ANSI: 6
[ 2.454048] scsi 0:0:0:2: Enclosure WD SES Device 1009 PQ: 0 ANSI: 6
[ 2.979649] SR 0: curr=1087500, delta_v=-94112, calc=993388, act=1000000, gain=1d
[ 2.993609] SR 1: curr=1200000, delta_v=-70822, calc=1129178, act=1137500, gain=29
[ 3.000121] Disabling lock debugging due to kernel taint
[ 3.001773] jnl: driver (lke_9.0.0 lke_9.0.0_r232673_b26, LBD=ON) loaded at bf000000
[ 3.189806] ufsd: module license ‘Commercial product’ taints kernel.
[ 3.226566] ufsd:: trace mask set to 0000000f
[ 3.226591] ufsd: driver (lke_9.0.0 lke_9.0.0_r232673_b26, LBD=ON, acl, ioctl, bdi, sd(0), fua, bz, tr) loaded at bf00b000
[ 3.226600] NTFS support included
[ 3.226604] exFAT support included
[ 3.226608] Hfs+/HfsJ support included
[ 3.226612] optimized: speed
[ 3.226615] Build_for__WD_Passport_wireless_k3.2.0_2013-10-15_lke_9.0.0_r232673_b26
[ 3.226622]
[ 3.594674] gpio_open
[ 3.594726] gpio_ioctl:cmd 1 gpio 27
[ 3.594747] Got irq = 187
[ 3.594874] gpio_ioctl:cmd 1 gpio 2
[ 3.594885] Got irq = 162
[ 3.594915] gpio_ioctl:cmd 1 gpio 3
[ 3.594925] Got irq = 163
[ 3.594962] gpio_release
[ 4.054798] Compat-wireless backport release: ol_r8.a8.08
[ 4.054815] Backport based on ol_r8.a8.08
[ 4.054822] compat.git:
[ 4.159018] cfg80211: Calling CRDA to update world regulatory domain
[ 4.172730] cfg80211: World regulatory domain updated:
[ 4.172751] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 4.172767] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 4.172780] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 4.172792] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
[ 4.172805] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 4.172817] cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
[ 4.704189] wlcore: wl18xx driver version:
[ 5.145601] wlcore: wl18xx HW: 183x or 180x, PG 2.2 (ROM 0x11)
[ 5.166969] wlcore: loaded
[ 5.167019] wlcore: driver version:
[ 5.167027] wlcore: compilation time: Wed Jan 15 11:46:00 2014
[ 9.159010] wlcore: PHY firmware version: Rev 8.2.WD.3.195
[ 9.211106] wlcore: firmware booted (Rev 8.8.0.280.13)
[ 9.487950] wlcore: down
[ 9.905776] wlcore: PHY firmware version: Rev 8.2.WD.3.195
[ 9.948580] wlcore: firmware booted (Rev 8.8.0.280.13)
[ 9.970130] cfg80211: Calling CRDA for country: GB
[ 9.971602] cfg80211: Regulatory domain changed to country: GB
[ 9.971619] cfg80211: DFS Master region ETSI
[ 9.971627] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
[ 9.971641] cfg80211: (2402000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 9.971653] cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 9.971664] cfg80211: (5250000 KHz - 5330000 KHz @ 40000 KHz), (N/A, 2000 mBm)
[ 9.971676] cfg80211: (5490000 KHz - 5710000 KHz @ 40000 KHz), (N/A, 2700 mBm)
[ 9.971688] cfg80211: (57240000 KHz - 65880000 KHz @ 2160000 KHz), (N/A, 4000 mBm)
[ 12.305998] device wlan1 entered promiscuous mode
[ 182.546388] sd 0:0:0:1: timing out command, waited 180s
[ 182.553976] sd 0:0:0:0: timing out command, waited 180s
[ 362.556390] sd 0:0:0:1: timing out command, waited 180s
[ 362.568617] sd 0:0:0:0: timing out command, waited 180s
[ 542.568457] sd 0:0:0:1: timing out command, waited 180s
[ 542.573980] sd 0:0:0:1: [sdb] Unit Not Ready
[ 542.578481] sd 0:0:0:1: [sdb] Sense Key : 0x4 [current]
[ 542.584143] sd 0:0:0:1: [sdb] ASC=0x30 <> ASCQ=0x89
[ 542.597539] sd 0:0:0:0: timing out command, waited 180s
[ 542.603064] sd 0:0:0:0: [sda] READ CAPACITY failed
[ 542.608104] sd 0:0:0:0: [sda] Result: hostbyte=0x00 driverbyte=0x08
[ 542.614760] sd 0:0:0:0: [sda] Sense Key : 0x4 [current]
[ 542.620429] sd 0:0:0:0: [sda] ASC=0x30 <> ASCQ=0x89
[ 722.597511] sd 0:0:0:1: timing out command, waited 180s
[ 722.647482] sd 0:0:0:0: timing out command, waited 180s
[ 722.653001] sd 0:0:0:0: [sda] Test WP failed, assume Write Enabled
ls -lrt /dev/sd*
ls: /dev/sd*: No such file or directory
