New Release - Firmware Version 2.10.12-129 for My Book Live (3/14/12)

Just an update/summary from me:

-Mistakenly applied the update, caused slow drive and funky lights and corrupt UI (page 7 of this thread)

-Called them, they sent new drive without prepaid label and they charged my credit or debit for the drive $280ish

-Updated new drive to the latest firmware before this broken one

-Copied Videos/Data to the new drive and deleted them from the old one

-Sent old drive back in package I got with the new one and paid ~$15 to send it

-Currently awaiting to be refunded $280

So basically, I’m short over $300 atm and awaiting a $280 refund. But I’m happy with my new drive on 2.10-124 or whatever.

If I have NO SSH enabled, and can not get into UI, is any way I can update the firmware ?

For those with Dashboard speed issues, ssh in and check to see that you aren’t getting errors on the nic interface.

For example, you don’t want to see any RX, TX packet errors on eth0:

MyBookLive:/etc# ifconfig -a
eth0      Link encap:Ethernet  HWaddr xx:xx:xx:xx:xx:xx 
          inet addr:192.168.1.103  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::290:a9ff:feb3:72f9/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:12460094 errors:0 dropped:0 overruns:0 frame:0
          TX packets:6491176 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:2768467156 (2.5 GiB)  TX bytes:564439955 (538.2 MiB)
          Interrupt:36

In reference to the fix to speed up UI:

If you´re like me and feel oooohhh so special that you have instantly renamed your drive :-) - then remember to change “MyBookLive” in the hosts file with your own name for the device.

BTW just received my 3TB version. Immediate impressions:

 - Updated from 128 → 129. Stuck at reboot but otherwise OK.

 - Can´t uninstall 1.5.0 WD NotSoSmartWare. I HATE having stuff in Windows I can´t clean up. BAD DOG, WD!

 - I have invested in an SSD and loving it but I actually find the MyBooks ticking and spinning annoying. Much more than in the reviews. Thinking of hiding it in a box. :slight_smile:

Random questions - If you by chance know the answer:

→ I want to put my dropbox local cache on the MyBook - bad idea?

→ I have a Samsung TV D7000. What special voodoo do I need to make things as good as possible?

→ Best way to test the transfer rate?

This is an awesome forum and with dedicated users. I appreciate every bit of information. WD should kiss you all - well almost all of you - on the forehead and say: “Thank you beautiful and valuable customer. You are the reason I exist. I promise to include a new version of Twonky soon and fix all the other stuff. Really. I proooooomise! Please send more money, though.”

jakobjb

You’re a genius ! completely solves the slow issue on my end!

congrats,

Rodolphe

can someone put a summary of how to resolve the dashboard slowness problem?Most of us are too late realize the problem AFTER upgrade the firmware…

Hi rodolgo, where is jakobjb’s post?

I bought My book live two days back and wanted to upgrade to the latest…I successfully upgraded but not without issues.

First thing I found out was that the firmware was very old. If I upgrade directly to latest it would fail because of some issues with Network update.

I followed the below method:

  1. Upgrade first to 124 version one and not 129 one

  2. Then upgrade to 129 version

  3. It will stop at 10 % and hang ( wait for 1 hour)

  4. Close the browser

  5. Open the browser and click on link to upgrade next to the red exclamatory mark. (Ignore the previous upgrade firmware display box)

  6. This time it will upgrade and install the new firmware.

Device is faster and better after this upgrade.

The one question everyone will ask is for the URLs to use in the browser to obtain the firmware files so a progressive upgrade can be performed.

Now I got a few firmware upgrade files but, alas, I assume (I’m sure someone from W.D. will be able to confirm?) I’m not allowed to provide links to my own copies, say, to a DropBox account because for one it’s not an official distribution and how can anyone know that such firmware files have not been infected or doctored.

Best place to get them is directly from W.D, so, where is the archive of firmware update files on W.D.'s site?  :smiley:

wangph wrote:

can someone put a summary of how to resolve the dashboard slowness problem?Most of us are too late realize the problem AFTER upgrade the firmware…

 

Hi rodolgo, where is jakobjb’s post?

Read this post

http://community.wdc.com/t5/My-Book-Live/New-Release-Firmware-Version-2-10-12-129-for-My-Book-Live-3-14/m-p/373795/highlight/true#M9909

And this (original Jakob’s post)

http://community.wdc.com/t5/My-Book-Live/New-Release-Firmware-Version-2-10-12-129-for-My-Book-Live-3-14/m-p/373625/highlight/true#M9889

Unfortunately I did not bookmark the download site.

problem resolved. thank you very much…

DrNicos wrote:

 

→ If you do not have SSH enabled, your only solution is to return the product for RMA replacement.

Well, that might not be entirely true. Here is my experience.

A month ago, I updated my MBL 1T, to 2.10.12-124. Soon after that the UI died. I checked with the community here, just to find out that, since I did not have ssh (or auto update) enabled I’m doomed. I had no time to spare, so i did not RMA the product.

Yestrday, the MBL would not show on the network and I could not connect to it or its media server at all, The LEDs on its ethernet port were as usual (one solid and the other blinking).

Without access to the UI to perform a safe reboot, I just disconnected and a 5 - 10 seconds later reconnected the MBL power adapter. The MBL booted (Blue LED followed by Red LED - it “lost” its green “touch” a long time ago) and shortly after, made itself available to the network.

At this point, I decided it would do no harm and tried the UI. Surprise, it WAS working. I checked for an update and got the network connection error. Went to WD’s site and found there was a new update (129). By the time the download was complete (and dinner was over), the UI had timed out and it was dead again.

After fiddling with the unplug/5 sec./plug procedure for a few times (performed on the the network cable too, just in case), the UI came back to life. I swiftly did a manual update (from within the UI), which went fine.

I did not encounter the slow UI issue, but there are some funny side effects.

According to the pics below, my MBL is for sure the oldest one on the planet (check the underlined dates).

But my MBL time/date info is correct and here is MBL’s message to prove it.

Hey WD, I’m ready to trade it for a new (“bigger”) one, and you can put in your museum :smileyvery-happy: .

So, before you RMA your new MBL for a refurbished one, due to the dead UI (with disabled ssh) issue, you might want to try the unplug/plug game of both the power and network cables. I know it doesn’t make sense but you never know…

Just spoke to tech support. After the tech assured me that resetting the device would not lose my data, it [delete] lost my data. [delete] Now I have to wait a day for level 2 support to call me back?

I have 2 Live TVs, a MybookLive, and 2 internal HDs. I’m going shopping to replace all of it. I’ll post a video of me destroying them all Office Space style when I’m done. I’m only a loyal customer if the company is loyal to me.

I can’t believe someone from Western Digital told you to reset the device. Any device reset to factory defaults will remove data and configuration. This is most basic. Maybe the person was not trained …

Got myself a 3TB SeaGate GoFlex Home, 2 NetGear NeoTVs and 2 SeaGate Barracudas all for less than $500 at BestBuy. I’ve cooled down some and decided not to destroy my WD stuff. I’ll be selling it on eBay (not the MBL obviously) and I expect my full investment in switching to decent vendors will be $250. That is waaaay less than the value of my data.

Goodbye WD.

update: i recieved a 3tb one that already had the latest update on it out of the box and after three attempts it works like a charm. can use all features

I’m sorry, I’m new to this “home network drive” kind thing.  Can someone help me step by step to make this new firmware 2.10.12-129 thing to work. 

I bought the 2t My book Live yesterday hoping I could back up all my computer and files to this drive and get web access.  I followed the instruction and get to the point I have to register with Mionet.  Did that and everything work fast and normal as expected.  I noticed the update on the dassboard and go ahead with that.  Followed the instruction not to exit while updating but i wait it for 5 hours and nothing happended.  I exit and closed the browser and get back on the dashboard.  Took about 1-2 mins to load the browser and the message said all update is completed.  Now everything work super slow and frustrated.  I’ve been reading all the post and get very confused.  Could anyone help me step by step where to go to and fix this problems.  Thank you very much.

I would like some advice please. I have just taken delivery of a new WD mybooklive 2Tb. The current firmware is 02.02.02-020. Should I update it to the current 02.10.12-129 or wait until the next update which according to this thread should appear sometime this month? or maybe update sto some intermidate version in the meantime?

many thanks

Barry

I bought My book live two weeks back and wanted to upgrade to the latest…I successfully upgraded but not without issues. First thing I found out was that the firmware was very old. If I upgrade directly to latest it would fail because of some issues with Network update. I followed the below method: 1) Upgrade first to 124 version first and not 129 one 2) Then upgrade to 129 version 3) It will stop at 10 % and hang ( wait for 1 hour) 4) Close the browser 5) Open the browser and click on link to upgrade next to the red exclamatory mark. (Ignore the previous upgrade firmware display box) 6) This time it will upgrade and install the new firmware.   Device is faster and better after this upgrade.

The previous tip should work 100 % . Use the below only if you have experience using command line. I struggled and got tips from other contributes. Collating so that you do not suffer. WD is good product but customer service is pathetic. If still not successful go for manual method: * Download the upgrade file using my PC, then copy the firmware (apnc-021012-129-20120308.deb) to the NAS public directory   *login to my NAS drive : ssh root@mybooklive.local *Manually update it : updateFirmwareFromFile.sh /DataVolume/shares/Public/apnc-021012-129-20120308.deb   * wait and it will reboot   output should be: MyBookLive:~#  updateFirmwareFromFile.sh /DataVolume/shares/Public/apnc-021012-129-20120308.deb version_newfile=021012129 version_current=021009124 package_newfile=apnc master_package_name=apnc