Is my drive failing?

The output of smartctl can be seen here - http://pastebin.com/43EyADTM

i am currently running smartctl -t long -C on that drive (which should complete in 4hrs)

Is there anything in that pastebin that indicates a path towards failure

Hello,

I recommend you run a diagnostic using WD DLG to determine the drive’s status.

Thanks. 

But the drive is on a Linux system. 

the smartctl output after tests

smartctl -a /dev/sdc

smartctl 5.41 2011-06-09 r3365 [x86_64-linux-3.2.0-4-amd64] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net

=== START OF INFORMATION SECTION ===
Device Model: WDC WD30EZRX-00DC0B0
Serial Number: WD-[Deleted][
LU WWN Device Id: 5 0014ee 6582907e6
Firmware Version: 80.00A80
User Capacity: 3,000,592,982,016 bytes [3.00 TB]
Sector Sizes: 512 bytes logical, 4096 bytes physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 9
ATA Standard is: Exact ATA specification draft version not indicated
Local Time is: Sun Oct 12 16:52:45 2014 SAST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (41520) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 255) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x70b5) SCT Status supported.
SCT Feature Control supported.
SCT Data Table supported.

SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE
1 Raw_Read_Error_Rate 0x002f 200 200 051 Pre-fail Always - 0
3 Spin_Up_Time 0x0027 195 177 021 Pre-fail Always - 5216
4 Start_Stop_Count 0x0032 100 100 000 Old_age Always - 168
5 Reallocated_Sector_Ct 0x0033 200 200 140 Pre-fail Always - 0
7 Seek_Error_Rate 0x002e 200 200 000 Old_age Always - 0
9 Power_On_Hours 0x0032 082 082 000 Old_age Always - 13316
10 Spin_Retry_Count 0x0032 100 100 000 Old_age Always - 0
11 Calibration_Retry_Count 0x0032 100 100 000 Old_age Always - 0
12 Power_Cycle_Count 0x0032 100 100 000 Old_age Always - 167
192 Power-Off_Retract_Count 0x0032 200 200 000 Old_age Always - 152
193 Load_Cycle_Count 0x0032 157 157 000 Old_age Always - 130226
194 Temperature_Celsius 0x0022 111 102 000 Old_age Always - 39
196 Reallocated_Event_Count 0x0032 200 200 000 Old_age Always - 0
197 Current_Pending_Sector 0x0032 200 200 000 Old_age Always - 0
198 Offline_Uncorrectable 0x0030 200 200 000 Old_age Offline - 0
199 UDMA_CRC_Error_Count 0x0032 200 200 000 Old_age Always - 0
200 Multi_Zone_Error_Rate 0x0008 200 200 000 Old_age Offline - 0

SMART Error Log Version: 1
Warning: ATA error count 27630 inconsistent with error log pointer 3

ATA Error Count: 27630 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It “wraps” after 49.710 days.

Error 27630 occurred at disk power-on lifetime: 13175 hours (548 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH


04 61 46 00 00 00 a0 Device Fault; Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name


ef 03 46 00 00 00 a0 00 21:38:30.991 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 00 21:38:30.991 IDENTIFY DEVICE
ec 00 00 00 00 00 a0 00 21:38:30.990 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 21:38:30.990 SET FEATURES [Set transfer mode]

Error 27629 occurred at disk power-on lifetime: 13175 hours (548 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH


04 61 46 00 00 00 a0 Device Fault; Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name


ef 03 46 00 00 00 a0 00 21:38:30.990 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 00 21:38:30.988 IDENTIFY DEVICE
ec 00 00 00 00 00 a0 00 21:38:30.987 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 21:38:30.987 SET FEATURES [Set transfer mode]

Error 27628 occurred at disk power-on lifetime: 13175 hours (548 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH


04 61 46 00 00 00 a0 Device Fault; Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name


ef 03 46 00 00 00 a0 00 21:38:30.987 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 00 21:38:30.987 IDENTIFY DEVICE
ec 00 00 00 00 00 a0 00 21:38:28.628 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 21:38:28.627 SET FEATURES [Set transfer mode]

Error 27627 occurred at disk power-on lifetime: 13175 hours (548 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH


04 61 46 00 00 00 a0 Device Fault; Error: ABRT

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name


ef 03 46 00 00 00 a0 00 21:38:28.627 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 00 21:38:28.627 IDENTIFY DEVICE
ca 00 08 00 10 00 e0 00 21:38:28.626 WRITE DMA
ec 00 00 00 00 00 a0 00 21:38:28.626 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 21:38:28.626 SET FEATURES [Set transfer mode]

Error 27626 occurred at disk power-on lifetime: 13175 hours (548 days + 23 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH


04 61 08 00 10 00 e0 Device Fault; Error: ABRT at LBA = 0x00001000 = 4096

Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name


ca 00 08 00 10 00 e0 00 21:38:28.626 WRITE DMA
ec 00 00 00 00 00 a0 00 21:38:28.626 IDENTIFY DEVICE
ef 03 46 00 00 00 a0 00 21:38:28.626 SET FEATURES [Set transfer mode]
ec 00 00 00 00 00 a0 00 21:38:28.626 IDENTIFY DEVICE
ca 00 08 00 10 00 e0 00 21:38:28.625 WRITE DMA

SMART Self-test log structure revision number 1
Num Test_Description Status Remaining LifeTime(hours) LBA_of_first_error

1 Extended offline Completed without error 00% 13309 -

2 Extended offline Interrupted (host reset) 90% 13301 -

3 Extended offline Aborted by host 30% 13300 -

4 Conveyance offline Completed without error 00% 13295 -

5 Short offline Completed without error 00% 13295 -

6 Short captive Interrupted (host reset) 90% 13295 -

7 Extended captive Interrupted (host reset) 90% 13276 -

8 Extended captive Interrupted (host reset) 90% 13224 -

SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.